Concrete Driveways in Oglesby, TX
Concrete driveways in Oglesby, TX get a mix held near a 4-inch slump, a broom-textured top for grip and isolation joints wherever they meet a walk or garage slab when Waco Elite Concrete pours them, and the estimate is free.
Call or request a free estimate any time, 24/7
No charge answered 24/7
Get free estimates
Bedrock, shrink-swell and the build of a drive
At the town's Census centre point, the county soil survey rates the Purves soil "Very limited" for concrete driveways and sidewalks and gives two reasons: depth to hard bedrock (1.00) and high shrink-swell (0.82). NRCS uses that rating where the limits generally can't be overcome without special design, costly installation or major soil reclamation, and where poor performance and high maintenance can be expected.
The mix and the joints come next. A driveway mix should arrive at about a 4-inch slump, never above the 5 inches the Portland Cement Association warns against, with the water-cement ratio kept under 0.50. Where new concrete meets old, the American Concrete Pavement Association calls for isolation joints ½ to 1 inch wide, filled full depth with a pre-formed filler.
The road end matters too. We found no published City rule for a new entrance, so ask the City, and a new or changed drive onto a state highway needs TxDOT's access permit through the Waco District office that covers Coryell County.
A walk from the drive to the door is covered on Oglesby sidewalks, and a patterned border on stamped concrete. See every service we offer in Oglesby for more.
Call or request a free estimate any time, 24/7.
(254) 309-9254A driveway from road to garage
Lay out and check the entrance
Width, length and thickness are set for the vehicles, and the City, County or TxDOT question is settled for the road end.
Base, forms and filler strips
Soft ground comes out, the base is compacted, and filler goes wherever the new slab meets old concrete or the garage.
Pour, broom and cut
The concrete is placed, broom-textured, and its control joints are cut a quarter of the slab deep.
Call or request a free estimate any time, 24/7.
(254) 309-9254What finish and steel add to a drive
In national 2025 figures a new concrete driveway runs $3,460 to $6,910, with $5,184 the average. Steel is priced separately in an older national guide (2023): wire mesh at $1.00 to $1.50 a square foot as material, rebar at $2 to $3 installed. Averages, not our prices.
- Plain
- $6 to $8
- Broom finished
- $8 to $12
- Exposed aggregate
- $8 to $12
- Stamped
- $12 to $18
National averages, 2025. Not a quote.
Questions about a new Oglesby drive
Does a driveway off a Coryell County road need a culvert?
If it crosses county right of way outside the city limits, Coryell County's driveway application applies. The County's Road and Bridge Department sets the culvert pipe's diameter and length, 24 feet is the shortest length allowed, and the application is void if the culvert isn't installed within 6 months. The form doesn't say whether it reaches inside the city, so ask the City there.
Should fiber be mixed into driveway concrete?
It can help early on. In NRMCA's guidance, synthetic fibers added at typical rates of 1 to 2 pounds per cubic yard cut down plastic shrinkage cracks and plastic settlement cracks, while macro-synthetic fibers, dosed at around 5 pounds per cubic yard, serve crack control once the concrete has hardened.
Is a broom finish or a smooth finish better on a driveway?
Broom. NRMCA's finishing guidance has exterior driveways, walks and patios textured with a push-broom after floating to give a non-slip surface.
Free driveway estimates for Oglesby
Choose driveway on the form and leave a phone number or email. There is no charge, and requests are answered 24/7.